Grandstream Device Configuration
STATUS BASIC SETTINGS ADVANCED SETTINGS PROFILE 1 PROFILE 2 FXS PORTS
Profile Active:   No      Yes
Primary SIP Server:   (e.g., sip.mycompany.com, or IP address)
Failover SIP Server:   (Optional, used when primary server no response)
Prefer Primary SIP Server:   No      Yes      ( yes - will register to Primary Server if Failover registration expires)
Outbound Proxy:   (e.g., proxy.myprovider.com, or IP address, if any)
SIP transport:   UDP       TCP       TLS   (default is UDP)
NAT Traversal:   No      Keep-Alive     STUN     UPnP
 
DNS Mode:   A Record      SRV      NAPTR/SRV
Tel URI:  
SIP Registration:    No       Yes
Unregister On Reboot:    No       Yes
Outgoing Call without Registration:    No       Yes
Register Expiration:   (in minutes. default 1 hour, max 45 days)
Reregister before Expiration:   (in seconds. Default 0 second)
SIP Registration Failure Retry Wait Time:   (in seconds. Between 1-3600, default is 20)
local SIP port:   (default 6060)
local RTP port:   (even number between 1024-65535, default 6004)
Use Random SIP Port:   No      Yes
Use Random RTP Port:   No      Yes
Refer-To Use Target Contact:   No      Yes
Transfer on Conference Hangup:   No      Yes
Disable Bellcore Style 3-Way Conference:   No      Yes (Using star code *23 for 3-way conference)
Remove OBP from Route Header:   No      Yes
Support SIP Instance ID:   No      Yes
Validate Incoming SIP Message:   No      Yes
Check SIP User ID for incoming INVITE:   No      Yes (no direct IP calling if Yes)
Authenticate incoming INVITE:   No      Yes
Allow Incoming SIP Messages
from SIP Proxy Only:
  No      Yes (no direct IP calling if Yes)
SIP T1 Timeout:  
SIP T2 Interval:  
DTMF Payload Type:  
Preferred DTMF method:
(in listed order)
  Priority 1:  
  Priority 2:  
  Priority 3:  
Disable DTMF Negotiation:   No (negotiate with peer) Yes (use above DTMF order without negotiation)
Send Hook Flash Event:   No      Yes   (Hook-Flash will be sent as a DTMF event if set to Yes)
Enable Call Features:   No      Yes (if Yes, call features using star codes will be supported locally)
Offhook Auto-Dial Delay:   (0-60 seconds, default is 0)
Proxy-Require:  
Use NAT IP:   (used in SIP/SDP message if specified)
Use SIP User-Agent Header:  
Distinctive Ring Tone:     used if incoming caller ID is
    used if incoming caller ID is
    used if incoming caller ID is
Disable Call-Waiting:   No      Yes
Disable Call-Waiting Caller ID:   No      Yes
Disable Call-Waiting Tone:   No      Yes
Disable Receiver Offhook Tone:   No      Yes   (ROH tone will not be played after offhook for 60 seconds)
Disable Reminder Ring for On-Hold Call:   No      Yes
Disable Visual MWI:   No      Yes
Ring Timeout:   (10-300, default is 60 seconds)
Hunting Group Ring Timeout:   (5-300, default is 20 seconds)
Hunting Group Type:   Circular    Linear
Delayed Call Forward Wait Time:   (Allowed range 1-120, in seconds.)
No Key Entry Timeout:   (in seconds, default is 4 seconds)
Early Dial:   No       Yes   (use "Yes" only if proxy supports 484 response)
Dial Plan Prefix:   (this prefix string is added to each dialed number)
Use # as Dial Key:   No       Yes   (if set to Yes, "#" will function as the "(Re-)Dial" key)
Dial Plan:  
SUBSCRIBE for MWI:   No, do not send SUBSCRIBE for Message Waiting Indication
  Yes, send periodical SUBSCRIBE for Message Waiting Indication
Send Anonymous:   No       Yes   (caller ID will be blocked if set to Yes)
Anonymous Call Rejection:   No       Yes  
Special Feature:  
Session Expiration:   (in seconds. default 180 seconds)
Min-SE:   (in seconds. default and minimum 90 seconds)
Caller Request Timer:   No     Yes (Request for timer when making outbound calls)
Callee Request Timer:   No     Yes (When caller supports timer but did not request one)
Force Timer:   No     Yes (Use timer even when remote party does not support)
UAC Specify Refresher:   UAC   UAS     Omit (Recommended)
UAS Specify Refresher:   UAC   UAS (When UAC did not specify refresher tag)
Force INVITE:   No     Yes (Always refresh with INVITE instead of UPDATE)
Send Re-INVITE After Fax:   No     Yes
Enable 100rel:   No     Yes
 
Use First Matching Vocoder in 200OK SDP:   No      Yes
Preferred Vocoder:
(in listed order)
  choice 1:  
  choice 2:  
  choice 3:  
  choice 4:  
  choice 5:  
  choice 6:  
G723 Rate:   6.3kbps encoding rate       5.3kbps encoding rate
iLBC Frame Size:   20ms       30ms
iLBC Payload Type:   (between 96 and 127, default is 97)
VAD:   No       Yes
Symmetric RTP:   No       Yes
Fax Mode:   T.38   Pass-Through
Re-INVITE After Fax Tone Detected:   Enabled   Disabled
Jitter buffer type:   Fixed   Adaptive
Jitter buffer length:   Low   Medium   High
SRTP Mode:   Disabled     Enabled but not forced   Enabled and forced
 
SLIC Setting:  
Caller ID Scheme:  
Polarity Reversal:   No      Yes   (reverse polarity upon call establishment and termination)
Loop Current Disconnect:   No      Yes   (loop current disconnect upon call termination)
Loop Current Disconnect Duration:   (In 100 - 10000 milliseconds range, default is 200)
Enable Hook Flash:   No      Yes  
Hook Flash Timing:   In 40-2000 milliseconds range, minimum:       maximum:
On Hook Timing:   (In 40-2000 milliseconds range, default is 400)
Gain:   TX   RX
Disable Line Echo Canceller (LEC):   No      Yes
 
Ring Tones (Syntax: c=on1/off1-on2/off2-on3/off3;)
Ring Tone 1:  
Ring Tone 2:  
Ring Tone 3:  
Ring Tone 4:  
Ring Tone 5:  
Ring Tone 6:  
Ring Tone 7:  
Ring Tone 8:  
Ring Tone 9:  
Ring Tone 10:  
        
All Rights Reserved Grandstream Networks, Inc. 2006-2012